The free beta is open. Apply to try the program →
Evolventix
Sheet 7 · who it's for

What does this program give me?

Short answer: anyone who cuts, prints or designs gears. You enter the measurement or the requirement; the program does the calculation, shows the problems and prepares the file for the machine, the printer or CAD. Find your own kind of work below.

What it asks of you

A few values such as tooth count, module or ratio. If you have an old gear, measurements taken with a caliper.

What it gives you

Checked gear geometry, fix suggestions, shop card, technical drawing, DXF, STEP, IGES, STL and a PDF report.

What is left to you

The final decision. You choose the material, load, heat treatment and manufacturing; the program gives suggestions and warnings on them.

Find yourself

What kind of work do you do?

Workshop and maintenance

“A gear broke in the machine and there is no drawing. How do I cut a new one?”

You enter the tooth count, tip diameter and span measurement (W); the program lists the most likely candidates for module and profile shift. You pick the hob or module cutter on your shelf, and the program calculates for that tool.

  • One-page Shop Card: tip diameter, infeed depth, Wk and ball dimension with tolerance
  • Finish Check while machining: “how much deeper should I cut?”
  • Module cutter number and dividing head setting (crank turns, hole circle)

Manufacturing: CNC, wire EDM, laser

“The customer only gave the module and tooth count. I need to draw the profile correctly.”

The involute profile is calculated from the standard basic rack (ISO 53), including the root fillet. A method is chosen for wire EDM and laser; the DXF goes straight to CAM.

  • DXF (2D profile), STEP and IGES (3D solid)
  • Tolerance and quality grade (based on IS 3681 / DIN 3961–3967)
  • Gear data table on the technical drawing (ISO 1340)

Machine design

“Ratio 3.5, 120 mm between shafts. Which gears, and will they hold?”

The wizard proposes pairs that pass the checks from the ratio and centre distance. Profile shift distribution, contact ratio and backlash are calculated; with torque, speed and material an ISO 6336 preliminary strength screening is done.

  • Spur, helical, double helical, internal, rack, worm, planetary, straight and spiral bevel
  • PDF report, transfer to CAD with STEP
  • Hub, hole and keyway in 3D Design

3D printing and hobby

“I printed two gears and they bind, or there is play.”

You choose the printer type (FDM or resin); the teeth are thinned by the print clearance. The wizard asks for the ratio and suggests the rest. This is the shortest route for someone with little gear knowledge.

  • STL ready for the slicer
  • Bore and keyway in the program
  • F1 explains the field the cursor is in

Students and teachers

“I know the formulas but I want to see and check the result.”

The Numbers tab shows the main values of the calculation with name, unit and explanation. Problems such as undercut, a thin tooth tip or a low contact ratio are shown with their reasons; change a value and see its effect at once.

Purchasing and technical office

“I need a drawing and inspection dimensions to send to the supplier.”

The technical drawing, data table and acceptance dimensions come from the program. You compare the incoming part with Wk or the ball dimension; Measurement Record records runout and deviations against the quality grade.

  • PDF technical drawing and shop card
  • Company name and project details in the title block
What you give, what you get

Five typical jobs, with their inputs and outputs.

JobYou enterThe program gives
A new gear for a broken oneTooth count, tip diameter, span measurement W over k and k + 1 teethCandidates for module, pressure angle and profile shift; a Shop Card and inspection dimensions for the candidate you pick
A gear pair with a given ratioRatio, distance between shafts, module if you likeTooth count suggestions, profile shift distribution, contact ratio, backlash; if there is a problem, its reason and a suggested fix
Preliminary strength checkTorque or power, speed, material, operating conditionsRoot and flank safety factors (SF, SH) with ISO 6336 methods, coloured result lights
Cutting with the tool you haveThe tools in your workshop, in the Tool LibraryA design that can be cut with that tool; the tool's dimensions are written into the design
Printing on a 3D printerRatio, printer typeTeeth with print clearance, bores, STL

For step-by-step instructions see the three sample jobs in the manual; to see it at work, watch the videos.

Let's be frank

What should you not expect from the program?

It is not a general-purpose CAD program.

The program's job is gears. The 3D Design window is for the gear's body (hub, holes, grooves, pockets). The sketch, plane and linear pattern tools are experimental; check the result. You combine other parts with STEP in your own CAD program.

The strength calculation is a preliminary screening.

It is calculated with ISO 6336 methods, but some factors are still taken as 1. The program does not guarantee load capacity; verify the calculation separately for critical parts. During the beta, Strength is open only to selected users.

“Fit for production” is not a guarantee.

It means the design has passed the program's geometry and production checks. Identification from measurements is also an estimate: compare the candidate you pick with the old part.

Windows and Turkish for now.

Windows 10 and 11, 64-bit. There is no macOS or Linux version. An English interface is in the trial stage. The assembly page is under development and closed for now. The program is in beta: you may see bugs; write to us.

Questions that come to mind

Questions

I know little about gears. Can I still use it?

Yes, the shortest route is the Wizard: choose what you want to do and enter the ratio or tooth count, and the program opens with a suggestion that has passed the checks. If a problem comes up, it states the reason and the Fix button suggests a solution. For the meaning of fields use F1, for the ideas the guides.

I already use hand calculations or a spreadsheet. What is the difference?

The formulas are the same; the difference is in the checks and the output. The program itself looks for undercut, a thin tooth tip, interference, low contact ratio and a thin rim, calculates inspection dimensions with tolerances, and carries the result straight to the shop card, drawing and file. A figure that could slip when copied by hand is entered once and goes everywhere the same.

How can I trust the calculations?

Calculation items are compared with independent methods and automated tests are run before every release. Which item is verified and how, and which is still partial, is stated openly in the verification report. Still, we recommend checking the result separately for a critical part.

Which programs open the outputs?

Standard file formats are used: DXF opens in most CAM and 2D drawing programs, STEP and IGES in 3D CAD programs, STL in slicers. The report, shop card and technical drawing are PDF.

What is expected of me in the beta?

That you use the program in your own work and tell us what you see. In the program, Help → Feedback prepares your email. During the beta every installation has all features except Strength unlocked for 30 days; no card details are asked for when you apply.

Will it be paid?

The beta is free. When sales start, editions and terms will be announced on this site.

Are my designs sent anywhere?

No. Project files stay only on your computer. The program works offline; if there is a connection it only checks for a new version, and that can be turned off in Settings.

What if the gear type I need is missing?

Write to us: destek@evolventix.com. Which type and which output people ask for is what we look at most when deciding the next work.

Try it in your own work.

The free beta is open. Fill in the form and the download link comes to your email. Before installing you can also try the calculator.

Apply for the free beta