The free beta is open. Apply to try the program →
Evolventix
Sheet 4 · guide 05 · design · ≈ 4 min

What is the minimum contact ratio?

The contact ratio tells how many tooth pairs touch at the same time on average during running. Below 1 the mesh breaks off, below 1.2 it is noisy.

What does it mean?

If the next tooth pair starts touching before one pair leaves the mesh, the mesh is continuous. The transverse contact ratio εα is how many tooth pairs touch on average along the mesh. If εα = 1.6, two tooth pairs touch for about 60% of the time and one pair for 40%. While two pairs touch, the load is shared; quiet running comes from this.

How is it calculated?

Divide the path of contact gα, the part of the line of action between the two tip circles, by the base pitch (pb = π·m·cos α). For a standard pair without profile shift:

εα = (√(ra1² − rb1²) + √(ra2² − rb2²) − a·sin α) ÷ (π·m·cos α)ra: tip radius, rb: base radius, a: centre distance
z1 = 20 z2 = 30 contact region, enlarged 3 times P N1 N2 A E gα pb gα = AE = 4.74·m · pb = 2.952·m → εα = 1.605
Figure 1. The line of action (N1N2) is tangent to the base circles of both gears; the teeth touch only between points A and E, where it cuts the two tip circles (orange). Above the general view, below the contact region enlarged. The ticks are base pitch pb intervals: they fit into the path of contact 1.6 times.

The result does not depend on the module; it depends only on the tooth counts:

z1z2εα (x = 0, α = 20°)
17171.515
20301.605
24241.602
18411.624
30601.719
1001001.853
many teethmany teeth→ 1.98

εα rises with the tooth count but levels off at 1.98; this is the limit for a rack with a gear of many teeth.

What should the minimum be?

εαMeaningIn the program
< 1.0The mesh breaks offBlocker
1.0 … 1.2Runs, noisyWarning (spur gear)
≥ 1.2Common design lower limit—

1.2 is a common design criterion, not a law. At low speed and where noise does not matter, 1.0–1.2 works, but as the contact ratio approaches 1 the load falls on a single tooth and the risk of breakage rises.

Try it · contact ratio

What raises it, what lowers it?

  1. Tooth count. As it rises, εα rises (see the table).
  2. Profile shift. As Σx becomes more positive, the centre distance grows and εα usually drops. For z₁ = 20, z₂ = 30: 1.605 with x₁ = x₂ = 0; 1.434 with x₁ = x₂ = +0.3. If Σx stays 0 (x₂ = −x₁), the change is small.
  3. Pressure angle. As α grows, the path of contact gets shorter. The same z₁ = 20, z₂ = 30 pair gives 1.442 at 25°.

On a helical gear

On a helical gear the overlap ratio is added to the transverse contact ratio: εγ = εα + εβ. The overlap ratio is εβ = b·sin β ÷ (π·mn) (b: face width, β: helix angle, mn: normal module). For b = 20 mm, β = 15°, mn = 2 mm, εβ = 0.82. That is why helical gears are quieter; for a helical gear the program gives no separate warning when εα < 1.2.

When choosing tooth counts, the program's Tooth Number Finder lists εα for each candidate pair.