The free beta is open. Apply to try the program →
Evolventix
Sheet 4 · guide 01 · measuring and identifying · ≈ 4 min

How do you find a gear's module?

You have a gear whose module is unknown. A caliper and the tooth count are enough: find the module with one of three methods and round it to the standard value.

First count the teeth

Count the number of teeth z; if you mark them with a pen as you count, you will not lose track. All three methods need z.

Method 1 · From the tip diameter

On a standard spur gear without profile shift the tip diameter is da = m·(z + 2). Measure da with a caliper and divide by z + 2.

m = da ÷ (z + 2)
Example

A gear with z = 24 teeth, the caliper shows da = 52.0 mm.

m = 52 ÷ (24 + 2) = 2

da = 52.0 mm z = 24
Figure 1. With an even tooth count, the tip diameter is measured across two opposite tooth tips.

If the tooth count is odd there is no tooth opposite. Measure from one tooth tip to the nearest tooth tip opposite and divide by cos(90° ÷ z). Example: if z = 25 and the reading is 53.89 mm, da = 53.89 ÷ cos 3.6° = 54.00 mm; m = 54 ÷ 27 = 2.

Try it · module from the tip diameter

Method 2 · From the base pitch

If the tooth tip is worn or there is profile shift, Method 1 goes wrong. This method ignores the tip: take the span measurement for two neighbouring tooth counts, and the difference gives the base pitch.

pb = Wk+1 − Wk = π·m·cos αat a 20° pressure angle m = pb ÷ 2.952
Example

z = 24: W₃ = 15.433 mm and W₄ = 21.337 mm were measured.

p_b = 21.337 − 15.433 = 5.904 → m = 5.904 ÷ 2.952 = 2.00

A pressure angle of 20° is assumed. Old gears may have 14.5°, some 25°; then cos α changes. The program's Identify Gear from Measurements tool takes your measurements and calculates and ranks likely candidates for module, pressure angle and profile shift in this way.

For how Wk is taken see the span measurement guide.

Video. Identify Gear from Measurements: module, pressure angle and profile shift are found from the tooth count, tip diameter and span measurements (18 s, no sound).

Method 3 · From the centre distance

If the gear pair is running, you only need the distance between the two shafts and the tooth counts.

m = 2·a ÷ (z1 + z2)
Example

Shaft distance a = 48 mm, z₁ = 18, z₂ = 30.

m = 2·48 ÷ (18 + 30) = 2

If the pair is profile shifted, the centre distance differs from the standard value; the result may not land on a standard module. That is a clue too.

Round to a standard module

The value you find should be very close to a module in the standard series:

11.251.522.53456810121620

Getting 2.02 because of caliper error is normal; round it to 2. If the value does not fit the series at all, one of the three traps below is present.

Three traps

  1. Helical gear. The diameter you measure with a caliper is in the transverse section. The normal module is mn = da ÷ (z ÷ cos β + 2); you also need to know the helix angle β. The easy way is Method 2.
  2. Profile shift. da = m·(z + 2 + 2x) with a shift, so Method 1 finds a module that is slightly too large. You can choose the standard module and get x from this: x = (da ÷ m − z − 2) ÷ 2. Example: z = 24, da = 53.0 mm, m = 2 gives x = +0.25. For what shifting is for, see the profile shift article .
  3. Inch gear. If a diametral pitch DP is given, m = 25.4 ÷ DP. For DP 12, m = 2.117; that is why it does not fit the standard series.

Found the module? Draw your gear: enter z and m in the calculator to get the diameters and span measurement.

Open the calculator