The free beta is open. Apply to try the program →
Evolventix
Sheet 4 · guide 03 · design · ≈ 5 min

What is profile shift for?

You move the cutting tool slightly away from the gear: the tooth gets thicker, undercut goes away, and the centre distance of a pair becomes adjustable.

The idea: moving the tool by x·m

On a standard gear the pitch line of the cutting tool is tangent to the gear's reference circle. With profile shift the tool is moved x·m away from the gear (x positive) or towards it (x negative). x is a dimensionless coefficient, m is the module.

The involute curve does not change; what changes is which part of the involute is used.

What does it change on a gear?

da = m·(z + 2 + 2x)
df = m·(z − 2.5 + 2x)
s = m·(π/2 + 2x·tan α)s: tooth thickness on the reference circle. The reference diameter d = m·z and the base diameter db do not change.
x = 0 · s = 1.571·m x = +0.5 · s = 1.935·m
Figure 1. z = 20, the same base circle. The involute is the same curve; x = +0.5 raises the tooth thickness from 3.142 mm to 3.870 mm (m = 2 mm) and the tip diameter from 44 mm to 46 mm. Dashed circles: reference (grey) and base circle (blue).

Example: z = 20, m = 2 mm. At x = 0, da = 44 mm, s = 3.142 mm. At x = +0.5, da = 46 mm, s = 3.870 mm: the tooth gets about 23% thicker and the root diameter rises from 35 mm to 37 mm. A thick tooth has a stronger root.

Try it · profile shift on one gear

In a pair: Σx and centre distance

In a pair the sum of the two profile shifts Σx = x₁ + x₂ sets the centre distance.

  1. If Σx = 0 (for example x₂ = −x₁), the centre distance stays at the standard a₀ = m·(z₁ + z₂) ÷ 2. The pinion with few teeth is shifted positive, the gear negative; the pinion's root gets stronger, the gear's root slightly weaker.
  2. If Σx > 0, the centre distance grows and the working pressure angle αw grows above 20°: inv αw = inv α + 2·Σx·tan α ÷ (z₁ + z₂); a = a₀·cos α ÷ cos αw. If the shaft distance differs from the standard value, you know the pair is shifted.

Example: z₁ = 12, z₂ = 30, m = 2 mm. Standard centre distance a₀ = 42 mm.

x₁ / x₂ΣxCentre distanceαwεα
+0.3 / −0.3042.00 mm20.00°1.480
+0.3 / 0+0.342.57 mm22.02°1.415
+0.3 / +0.3+0.643.10 mm23.69°1.350

When Σx ≠ 0 the program shortens the tips slightly (so that the bottom clearance stays 0.25·m); the εα in the table includes this. For what the contact ratio means, see the contact ratio article.

Limits

The lower limit is set by undercut: x ≥ xmin (undercut article). The upper limit is set by the tooth tip: positive x thins the tooth, and with a very large x the flanks meet before reaching the tip circle (pointed tooth). The program warns when the tip thickness is below 0.4·m and gives a blocker below 0.2·m.

x (z = 20)Tip thicknessProgram
00.69·mfine
+0.500.47·mfine
+0.750.33·mthin, warning
+1.000.16·mvery thin, production blocker
+1.25—pointed tooth

In the program

On the gear, pair and rack screens you enter x by hand or leave it automatic; automatic x = max(0, xmin). If you give the centre distance, the program finds Σx and splits it between the two gears; the default split is equal specific sliding at the root.

Change x on one gear and see on the drawing how the tip diameter, tooth thickness and tooth tip move.

Open the calculator